Console

1. Hyper-Terminal

   9600 N 8 1 None

   Default Username: admin (no password)

    

2. Main Function

   Enterprise AP#?
   Exec commands:   
      bootfile     Specify Application Bootfile
      configure   Enter configuration mode
      copy         Copy datafiles to/from the access point
      delete       Delete a file
      dir            List files on a file system
      exit          Exit from the EXEC
      help         Description of the help system
      ping         Send echo messages
      reset        Reset this system
      show        Display access point operation information

    

3. Configure

   Enterprise AP#reset ?
      board              reset the access point
      configuration    reset configuration to factory default

   Enterprise AP#reset configuration
   Reset to Factory Defaults now?<y/n>:y <Enter>

   Enterprise AP#config
   Enter configuration commands, one per line.  

   Enterprise AP(config)#interface ?
   ethernet Into Ethernet configuration mode
   wireless Into Wireless configuration mode

   Enterprise AP(config)#interface ethernet

   Enterprise AP(if-ethernet)#ip address 10.4.24.81 255.255.255.0 10.4.24.1
   No IP configuration allowed while DHCP is enabled.

   Enterprise AP(if-ethernet)#no ip dhcp
   Enterprise AP(if-ethernet)#ip address 10.4.24.81 255.255.255.0 10.4.24.1

   Enterprise AP(if-ethernet)#exit
   Enterprise AP#config
   Enter configuration commands, one per line.  

   Enterprise AP(config)#ip ?
   http Set IP HTTP server configuration
   https Set IP HTTP secure server configuration
   Enterprise AP(config)#ip http ?
   port Set IP Port number of the HTTP
   server Enable HTTP server
   session-timeout Set session timeout of the HTTP server
   Enterprise AP(config)#ip http server ?
   <cr>
   Enterprise AP(config)#ip http server
   Enterprise AP(config)#ip https server

   (You should be able to connect to Web Interface now, 
   but need to connect to VLAN 10's switch port not the trunking port yet)

    

4. Show Interface

   Enterprise AP#show interface

   Ethernet Interface Information
   ========================================
   IP Address : 10.4.24.81
   Subnet Mask : 255.255.255.0
   Default Gateway : 10.4.24.1
   Primary DNS : 207.47.4.2
   Secondary DNS : 216.237.6.36
   Admin status : Up
   Operational status : Up
   ========================================

    

5. Show Config

   Enterprise AP#show config

   Authentication Information
   ===========================================================
   MAC Authentication Server : DISABLED
   MAC Auth Session Timeout Value : 0 min
   802.1x supplicant : DISABLED
   802.1x supplicant user : EMPTY
   802.1x supplicant password : EMPTY
   Address Filtering : ALLOWED

   System Default : ALLOW addresses not found in filter table.
   Filter Table
   -----------------------------------------------------------
   No Filter Entries.
   ===========================================================
   Press <n> next. <p> previous. <a> abort. <y> continue to end :

    

6. Management VLAN ID :

   To set the native VLAN ID same as Web GUI: VLAN_Configuration

   (Be carefully about change this setting, once you enable the VLAN then have to switch to the trunk port and once you disable it then have to switch to the access port)

   Enterprise AP(config)#management-vlanid ?
   <1-4094> Set Management VLAN ID for AP <1-4094>
   Enterprise AP(config)#management-vlanid 10

    

7. System Name (Identification):

   Same as Web GUI: AP_ID:_we_use_TCNW01_~_TCNW13

   Enterprise AP(config)#system ?
   name Set system name
   Enterprise AP(config)#system name ?
   LINE Set system name
   Enterprise AP(config)#system name TCNW01

    

8. Setup admin password

   Same as Web GUI: Administration_(admin_password)

   Enterprise AP(config)#password ?
   WORD Assign the password
   Enterprise AP(config)#password Password (be careful, it will not encrypt the password on you typing, so make nobody copy it while you are typing)

    

9. vlan-ID

   Same as Web GUI: vlan-ID

   Enterprise AP(config)#interface wireless g
   Enter Wireless configuration commands, one per line.

   Enterprise AP(if-wireless g)#vap ?
   <0-7> 6 in turbo mode
   Enterprise AP(if-wireless g)#vap 0

   Enterprise AP(if-wireless g: VAP[0])#vlan-ID ?
   <1-4094> Set default vlan ID
   Enterprise AP(if-wireless g: VAP[0])#vlan-ID 10

   Enterprise AP(if-wireless g: VAP[0])#end
   Enterprise AP(if-wireless g)#vap 1
   Enterprise AP(if-wireless g: VAP[1])#vlan-
   Enterprise AP(if-wireless g: VAP[1])#vlan-ID 100

    

10. ssid:

    Same as Web GUI: Radio_G_Setting

    Enterprise AP(if-wireless g: VAP[0])#ssid ?
    LINE Set wireless ssid (max 32 characters)
    Enterprise AP(if-wireless g: VAP[0])#ssid nwtc-office

    Enterprise AP(if-wireless g: VAP[0])#end
    Enterprise AP(if-wireless g)#vap 1
    Enterprise AP(if-wireless g: VAP[1])#ssid nwtc-clp

     

11. Shutdown none used VAP2 ~ VAP7

    Same as Web GUI: Radio_G_Setting

    Enterprise AP(if-wireless g: VAP[2])#end
    Enterprise AP(if-wireless g)#vap 2
    Enterprise AP(if-wireless g: VAP[2])#shutdown

                ~

    Enterprise AP(if-wireless g: VAP[6])#end
    Enterprise AP(if-wireless g)#vap 7
    Enterprise AP(if-wireless g: VAP[7])#shutdown

     

12. auth wpa-psk setup

    Same as Web GUI: Radio_G_Security

    Enterprise AP(if-wireless g: VAP[0])#auth wpa-psk ?
    required Set Required mode
    supported Set Supported mode
    Enterprise AP(if-wireless g: VAP[0])#auth wpa-psk required
    Data Encryption is set to Enabled.
    WPA2 Clients Mode is set to Disabled.
    WPA Clients Mode is set to Required.
    WPA Multicast Cipher is set to TKIP.
    WPA Unicast Cipher can accept TKIP only.
    WPA Authentication is set to Pre-Shared Key.

     

13. Enable encryption

    Same as Web GUI: Radio_G_Security

    Enterprise AP(if-wireless g: VAP[0])#encryption

     

14. wpa-pre-shared-key

    Same as Web GUI: Radio_G_Security

    Enterprise AP(if-wireless g: VAP[0])#wpa-pre-shared-key ?
    hex Set hex key type
    passphrase-key Set passphase key type
    Enterprise AP(if-wireless g: VAP[0])#wpa-pre-shared-key passphrase-key ?
    LINE Set the key value
    Enterprise AP(if-wireless g: VAP[0])#wpa-pre-shared-key passphrase-key 1234
    ASCII keys must be atleast 8 alphanumeric characters.
    Enterprise AP(if-wireless g: VAP[0])#wpa-pre-shared-key passphrase-key 12345678

     

15. Pre-Authentication

    Same as Web GUI: Radio_G_Security

    Enterprise AP(if-wireless g: VAP[0])#pre-authentication enable