Edge Core AP - Console

Console

Hyper-Terminal
9600 N 8 1 None

Default Username: admin (no password)
Main Function
Enterprise AP#?
Exec commands:
   bootfile     Specify Application Bootfile
   configure   Enter configuration mode
   copy         Copy datafiles to/from the access point
   delete       Delete a file
   dir            List files on a file system
   exit          Exit from the EXEC
   help         Description of the help system
   ping         Send echo messages
   reset        Reset this system
   show        Display access point operation information
Configure
Enterprise AP#reset ?
   board              reset the access point
   configuration    reset configuration to factory default

Enterprise AP#reset configuration
Reset to Factory Defaults now?<y/n>:y <Enter>

Enterprise AP#config
Enter configuration commands, one per line.

Enterprise AP(config)#interface ?
ethernet Into Ethernet configuration mode
wireless Into Wireless configuration mode

Enterprise AP(config)#interface ethernet

Enterprise AP(if-ethernet)#ip address 10.4.24.81 255.255.255.0 10.4.24.1
No IP configuration allowed while DHCP is enabled.

Enterprise AP(if-ethernet)#no ip dhcp
Enterprise AP(if-ethernet)#ip address 10.4.24.81 255.255.255.0 10.4.24.1

Enterprise AP(if-ethernet)#exit
Enterprise AP#config
Enter configuration commands, one per line.

Enterprise AP(config)#ip ?
http Set IP HTTP server configuration
https Set IP HTTP secure server configuration
Enterprise AP(config)#ip http ?
port Set IP Port number of the HTTP
server Enable HTTP server
session-timeout Set session timeout of the HTTP server
Enterprise AP(config)#ip http server ?
<cr>
Enterprise AP(config)#ip http server
Enterprise AP(config)#ip https server

(You should be able to connect to Web Interface now,
but need to connect to VLAN 10's switch port not the trunking port yet)
Show Interface
Enterprise AP#show interface

Ethernet Interface Information
========================================
IP Address : 10.4.24.81
Subnet Mask : 255.255.255.0
Default Gateway : 10.4.24.1
Primary DNS : 207.47.4.2
Secondary DNS : 216.237.6.36
Admin status : Up
Operational status : Up
========================================
Show Config
Enterprise AP#show config

Authentication Information
===========================================================
MAC Authentication Server : DISABLED
MAC Auth Session Timeout Value : 0 min
802.1x supplicant : DISABLED
802.1x supplicant user : EMPTY
802.1x supplicant password : EMPTY
Address Filtering : ALLOWED

System Default : ALLOW addresses not found in filter table.
Filter Table
-----------------------------------------------------------
No Filter Entries.
===========================================================
Press <n> next. <p> previous. <a> abort. <y> continue to end :
Management VLAN ID :
To set the native VLAN ID same as Web GUI: VLAN_Configuration

(Be carefully about change this setting, once you enable the VLAN then have to switch to the trunk port and once you disable it then have to switch to the access port)

Enterprise AP(config)#management-vlanid ?
<1-4094> Set Management VLAN ID for AP <1-4094>
Enterprise AP(config)#management-vlanid 10
System Name (Identification):
Same as Web GUI: AP_ID:_we_use_TCNW01_~_TCNW13

Enterprise AP(config)#system ?
name Set system name
Enterprise AP(config)#system name ?
LINE Set system name
Enterprise AP(config)#system name TCNW01
Setup admin password
Same as Web GUI: Administration_(admin_password)

Enterprise AP(config)#password ?
WORD Assign the password
Enterprise AP(config)#password Password (be careful, it will not encrypt the password on you typing, so make nobody copy it while you are typing)
vlan-ID
Same as Web GUI: vlan-ID

Enterprise AP(config)#interface wireless g
Enter Wireless configuration commands, one per line.

Enterprise AP(if-wireless g)#vap ?
<0-7> 6 in turbo mode
Enterprise AP(if-wireless g)#vap 0

Enterprise AP(if-wireless g: VAP[0])#vlan-ID ?
<1-4094> Set default vlan ID
Enterprise AP(if-wireless g: VAP[0])#vlan-ID 10

Enterprise AP(if-wireless g: VAP[0])#end
Enterprise AP(if-wireless g)#vap 1
Enterprise AP(if-wireless g: VAP[1])#vlan-
Enterprise AP(if-wireless g: VAP[1])#vlan-ID 100
ssid:
Same as Web GUI: Radio_G_Setting

Enterprise AP(if-wireless g: VAP[0])#ssid ?
LINE Set wireless ssid (max 32 characters)
Enterprise AP(if-wireless g: VAP[0])#ssid nwtc-office

Enterprise AP(if-wireless g: VAP[0])#end
Enterprise AP(if-wireless g)#vap 1
Enterprise AP(if-wireless g: VAP[1])#ssid nwtc-clp
Shutdown none used VAP2 ~ VAP7
Same as Web GUI: Radio_G_Setting

Enterprise AP(if-wireless g: VAP[2])#end
Enterprise AP(if-wireless g)#vap 2
Enterprise AP(if-wireless g: VAP[2])#shutdown

~

Enterprise AP(if-wireless g: VAP[6])#end
Enterprise AP(if-wireless g)#vap 7
Enterprise AP(if-wireless g: VAP[7])#shutdown
auth wpa-psk setup
Same as Web GUI: Radio_G_Security

Enterprise AP(if-wireless g: VAP[0])#auth wpa-psk ?
required Set Required mode
supported Set Supported mode
Enterprise AP(if-wireless g: VAP[0])#auth wpa-psk required
Data Encryption is set to Enabled.
WPA2 Clients Mode is set to Disabled.
WPA Clients Mode is set to Required.
WPA Multicast Cipher is set to TKIP.
WPA Unicast Cipher can accept TKIP only.
WPA Authentication is set to Pre-Shared Key.
Enable encryption
Same as Web GUI: Radio_G_Security

Enterprise AP(if-wireless g: VAP[0])#encryption
wpa-pre-shared-key
Same as Web GUI: Radio_G_Security

Enterprise AP(if-wireless g: VAP[0])#wpa-pre-shared-key ?
hex Set hex key type
passphrase-key Set passphase key type
Enterprise AP(if-wireless g: VAP[0])#wpa-pre-shared-key passphrase-key ?
LINE Set the key value
Enterprise AP(if-wireless g: VAP[0])#wpa-pre-shared-key passphrase-key 1234
ASCII keys must be atleast 8 alphanumeric characters.
Enterprise AP(if-wireless g: VAP[0])#wpa-pre-shared-key passphrase-key 12345678
Pre-Authentication
Same as Web GUI: Radio_G_Security

Enterprise AP(if-wireless g: VAP[0])#pre-authentication enable